1021 DR Tuesday EngFit MOET TechSup
Section | Name | Description |
---|---|---|
QPEO2 001 Health and Safety | Health and Safety in Engineering | A general Health and safety unit to cover legislation, Responcibilities, Manual handling and COSHH matters within the engineering environment. |
Manual handling paperwork | Contained in this file is the paperwork required for you Manual Handling Practical assessment. |
|
Risk assessment forms | Contains all forms required for risk assessments. |
|
Moving a heavy load report | Report for folder evidance to show an understanding of the process |
|
H&S | H&S |
|
HASAW 1974 | HASWA 1974 Leaflet |
|
PUWER | Provision and Use of Work Equipment Regulations 1998 |
|
IP Codes | International Protection codes (Ingress of foreign bodies and water) |
|
Management of HASAWA | Management of HASAWA |
|
Low Voltage Switch-gear | Guide to Low Voltage Switch-gear |
|
Low Voltage Switchgear and Controlgear Assemblies in Accordance with BS EN 61439 series | BEAMA GUIDE TO VERIFICATION OF TEMPERATURE RISE AND SHORT:CIRCUIT WITHSTAND OTHER THAN BY TEST Low Voltage Switchgear and Controlgear Assemblies in Accordance with BS EN 61439 series |
|
Panel Wiring Useful links | ||
EAL-AUEC2-009 - Maintaining Electrical Equipment-Systems | EAL-AUEC2-009 - Maintaining Electrical Equipment-Systems |
|
QPEO2 002 Working effectively in the engineering environment | Site Supervisor | All Learners must complete at least two site supervisor forms for practical activities within the PETA training area at Havant. The learner will be given this responsibility by the instructor and forms should be added to Unit 002 of the learners evidence folder. |
NICEIC Power Points | NICEIC Power Points |
|
Assignments 1 and 2 | Assignments 1 and 2 |
|
Circuits | Circuits |
|
Basic electrical book | Please read this Introduction to Basic electrical Installation |
|
Panel Wiring | Useful Information |
|
Material Conductance | Electrical Conductivity of Materials |
|
Protection against Electric Shock | Automatic Disconection of supply includes Insulation, Earthing and (OCPD overcurrent protective devices) Earth fault Loop Zs |
|
Risk assessment Electrical | To evaluate risk and safe working practices during workshop activities and assessments. |
|
Good Crimping Guide | The Secret to a Successful Crimp Wire Prep - In order to properly place a wire in a terminal, the wire insulation must fi rst be stripped to the proper length based on the terminal specifications. If the insulation is cut too short or too long, the wire will not be seated properly into the wire barrel, causing terminal separations or shorting |
|
QPEO2 003 Understanding technical Information | Understanding technical information | This will guide you through information regarding technical information. |
Drawing booklet | A booklet designed to give an understanding of how to complete technical drawings. |
|
Hand Fitting | QPEO2-005 Hand Fitting | This module is designed to teach the basic hand fitting / bench fitting techniques at level 2. |
AUEC2-009 | Safe Isolation Guide | Safe Isolation Guide Electrical Safety First |
Safe Isolation Guide | Pocket Guide for safe Isolation |
|
EAWR 1989 | The Electricity at Work Regulations 1989 |
|
BS7671 18th wiring Regulations | Non-Statutory British standard wiring regulations 2018 |
|
EAWR 1989 | EAWR 1989 |
|
EAL-AUEC2-009 - Maintaining Electrical Equipment-Systems | EAL-AUEC2-009 - Maintaining Electrical Equipment-Systems |
|
Resistance of conductors R1 + R2 | Resistance of conductors R1 + R2 |
|
Resistance | Resistance series and parallel |
|
GN3 | GN3 |
|
Continuity testing Video |
|
|
Insulation resistance test |
|
|
Continuity of CPC (R1 + R2) and Polarity of our 2 Way Lighting Circuit and Insulation Resistance |
|
|
Cables and fixings | Cables and fixings |
|
Testing procedures | Testing procedures |
|
Testing Power point | Testing Power point |
|
AUEC2-030 CAD | DSE risk assessment form | DSE risk assessment to be filled out and attached to each assignment |
Handouts | ||
Drawing Standards | National and International standards relating to engineering drawing practice |
|
AUEC2-044 MIG Welding | Drawings | Drawings to be attached to your MIG welding Report |